Thanks for detailed instructions with image. We have attached pump target system to north wall as explained. Rajesh Shah Coach Team #31778 On Sun, Sep 10, 2017 at 11:30 AM, VA-DC Referee Advisor <[log in to unmask]> wrote: > Part 2: > > In the Mission Models (Advanced Setups) section, it gives the > instructions for attaching the Pump System. The figure for Step 1 shows > where to put dual lock on the Pump System. Since the picture is > low-resolution, here's what to do: use 6 pairs of dual lock. I've > included a picture showing where they go on one side. > > One at the top of the long gray piece on the centerline of the round > part. > One at the bottom of the round part, also on the long gray piece. > One diagonally at the bottom of the long gray piece above the round part. > > Once you have the 6 pairs of dual lock attached to the model (you'll > have sticky sides out on the outside of the pairs), line the model up > between its marks and push north to attach to the North wall. The Pump > System will still be sitting on the Mat. > > Steve Scherr > VA-DC FLL Referee Advisor > > > On Sun, Sep 10, 2017 at 11:09 AM, VA-DC Referee Advisor <[log in to unmask]> > wrote: > >> Hello everyone, >> >> The Pump model does need to be attached to the North wall. >> >> As stated in the Field Setup document, "The Mat is smaller than the >> playing surface by design." Step 3 of the Field Mat Placement section, >> says to align the mat so there is no gap at the South wall, and equal gaps >> at the East and West walls. So there is going to be a gap at the North >> wall. Teams--remember that the North wall gap may vary a little between >> your practice table and a tournament table. >> >> >> >> On Sun, Sep 10, 2017 at 9:39 AM, Cedric D'Costa < >> [log in to unmask]> wrote: >> >>> Thank you VA/DC FLL for organizing the very informative worshop in >>> Reston, VA on Friday. >>> I had brought up this question there as the worshop table Pump system >>> model (similar to my team) had not stuck the model to the north border >>> wall. >>> >>> In order to stick the model to the wall, it needs to be slightly outside >>> the mat. There is a small gap between the mat and the north wall and the >>> mat itself has a black border. In order to keep the model on the mat we >>> would need to add additional Lego pieces or something to fill the gap and >>> have the model make contact with the wall. >>> >>> The field set up guide does not offer information regarding this. >>> However on page 13 it apppears as though the model is slightly outside the >>> mat. >>> >>> Referees, coaches please repond. >>> >>> Thank you, >>> Cedric D'Costa >>> Coach Team# 18179 >>> >>> >>> -------- Original message -------- >>> From: Rajesh Shah <[log in to unmask]> >>> Date: 09/09/2017 6:47 PM (GMT-05:00) >>> To: [log in to unmask] >>> Subject: [VADCFLL-L] FLL hydro dynamics field setup question >>> >>> We are trying to figure out how the pump target system is attached to >>> the north wall of the table using dual locks as mentioned in field setup >>> guide. Any suggestion? >>> >>> Thanks! >>> Rajesh Shah >>> Coach Team #31778 >>> >>> ------------------------------ >>> To UNSUBSCRIBE or CHANGE your settings, please visit >>> https://listserv.jmu.edu/archives/vadcfll-l.html and select "Join or >>> leave the list". >>> VADCFLL administrative announcements are sent via >>> VADCFLL-ANNOUNCEMENTS-L. Visit https://listserv.jmu.edu/archi >>> ves/vadcfll-announcements-l.html to subscribe. >>> ------------------------------ >>> To UNSUBSCRIBE or CHANGE your settings, please visit >>> https://listserv.jmu.edu/archives/vadcfll-l.html and select "Join or >>> leave the list". >>> VADCFLL administrative announcements are sent via >>> VADCFLL-ANNOUNCEMENTS-L. Visit https://listserv.jmu.edu/archi >>> ves/vadcfll-announcements-l.html to subscribe. >>> >> >> > ------------------------------ > To UNSUBSCRIBE or CHANGE your settings, please visit > https://listserv.jmu.edu/archives/vadcfll-l.html and select "Join or > leave the list". > VADCFLL administrative announcements are sent via VADCFLL-ANNOUNCEMENTS-L. > Visit https://listserv.jmu.edu/archives/vadcfll-announcements-l.html to > subscribe. > -- To UNSUBSCRIBE or CHANGE your settings, please visit https://listserv.jmu.edu/archives/vadcfll-l.html and select "Join or leave the list". -- VADCFLL administrative announcements are sent via VADCFLL-ANNOUNCEMENTS-L. Visit https://listserv.jmu.edu/archives/vadcfll-ANNOUNCEMENTS-l.html to subscribe.