Print

Print


Donald,

 

I agree with Sonya – call LEGO Education.  They may want to go through some troubleshooting (a repeat of what you’ve aleady done) but they have always been great about replacing faulty bricks.

 

Nick

 

From: First Lego League in Virginia and DC <[log in to unmask]> On Behalf Of Sonya Shaver
Sent: Thursday, June 6, 2019 2:36 PM
To: [log in to unmask]
Subject: Re: [VADCFLL-L] Help with NXT light and sound sensors

 

Hi Donald,

The technical consumer service team at LEGO Education should be able to help you.  For the phone number and hours, see this link:

 

https://education.lego.com/en-us/support

 

Hope that helps!  Please let us know if you need further assistance.

 

Best regards,

Sonya

 

From: First Lego League in Virginia and DC <[log in to unmask]> On Behalf Of Donald Williams
Sent: Thursday, June 6, 2019 2:13 PM
To: [log in to unmask]
Subject: [EXTERNAL] Re: [VADCFLL-L] Help with NXT light and sound sensors

 

It turns out that I looked at this and determined the problem to some certainty:

https://bricks.stackexchange.com/questions/10586/nxt-sensors-not-working/10617#10617 

 

Using a volt meter, and checking pins 3 and 4 with the robot ON, I was able to tell that there was no voltage going to the sensor. I set the screen to "View" > sensor > port # and checked the voltage. On a good robot, I get near 4.5V. On my suspect robot, I get 0.02V.

 

Have any of you ever repaired a problem such as this?

 

Just sharing my experience with you, and looking for next step. 

 

 

Donald Williams P.E.

Phoebus High School

100 Ireland Street

Hampton, VA 23663

757-727-1031

 

 

 

 

On Thu, Jun 6, 2019 at 12:48 PM Donald Williams <[log in to unmask]> wrote:

I haven't used the robots for a while and when I get them out, and I can write programs and load the programs onto 12 robots. 11 of the robots work fine, but one won't recognize the light or sound sensor. It recognizes a touch sensor. I have verified the sensors works by swapping sensors and cables with other  robots (multiple times, with another teacher who is an electrical engineer watching). If I try going to "View" the sensors (on the correct ports), I get a value of "0". I have reloaded the firmware.

 

Any ideas?

 

 

Donald Williams P.E.

Phoebus High School

100 Ireland Street

Hampton, VA 23663

757-727-1031

 

 

 

----

CONFIDENTIALITY NOTICE:  This email message, including any attachments, is for the sole use of the

intended recipient(s) and may contain information that is legally privileged, confidential and/or exempt from

disclosure under applicable law.  If you are not an intended recipient, you may not review, use, copy, disclose

or distribute this message or any of the information contained in this message to anyone.  If you are not the intended

recipient, please contact the sender by reply email and destroy all copies of this message and any

attachments.  Hampton City Schools may monitor e-mail messages to and from the Hampton City Schools

network.   Unintended transmission shall not constitute waiver of any privilege or confidentiality protected under

federal statutes, the Virginia Freedom of Information Act or any applicable laws.


To UNSUBSCRIBE or CHANGE your settings, please visit https://listserv.jmu.edu/archives/vadcfll-l.html and select "Join or leave the list".
VADCFLL administrative announcements are sent via VADCFLL-ANNOUNCEMENTS-L. Visit https://listserv.jmu.edu/archives/vadcfll-announcements-l.html to subscribe.


To UNSUBSCRIBE or CHANGE your settings, please visit https://listserv.jmu.edu/archives/vadcfll-l.html and select "Join or leave the list".
VADCFLL administrative announcements are sent via VADCFLL-ANNOUNCEMENTS-L. Visit https://listserv.jmu.edu/archives/vadcfll-announcements-l.html to subscribe.


To UNSUBSCRIBE or CHANGE your settings, please visit https://listserv.jmu.edu/archives/vadcfll-l.html and select "Join or leave the list".
VADCFLL administrative announcements are sent via VADCFLL-ANNOUNCEMENTS-L. Visit https://listserv.jmu.edu/archives/vadcfll-announcements-l.html to subscribe.